Just How to Replace a Bathtub in Your Bathroom
Just How to Replace a Bathtub in Your Bathroom
Blog Article
On this page in the next paragraph yow will discover a good deal of decent information and facts relating to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough task. If the old tub is easily obtainable, the job can relocate speedily; if you need to open up a wall surface to remove the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly need an assistant to move out the old tub and also embeded in the brand-new one. Make sure you have certified yourself for the work and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your restroom if you have already bought a brand-new bathtub as well as do not need to alter the plan of your previous water pipes.
Your tools as well as product checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be rather bothersome as a result of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water supply and also check all joints and also brand-new pipework for leakages and also tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been utilized at the very least when as this will settle it into its last placement.
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that blog posting about How to Install a Bathtub Yourself when surfing around the web. For those who liked our page if you please make sure you remember to share it. Thank you so much for your time invested reading it.
Go Deal Report this page